[SHAULA-V10] Basic Manual

0 Comments

INTRODUCTION

SHAULA-V10 is a GSM gateway that can provide SMS and Call features for different Alarm systems. The features and functions may vary with firmware versions slightly but in general they are consistent. Below is the summary of features.

  • operate gate and door (via two relay on board with C and NC contacts).
  • arm & disarm alarm control panel using the app.
  • make alert calls in case of intrusion alarm, panic alarm or fire alarm.
  • monitor power source notify by SMS if it goes or when it comes back.
  • monitor backup battery when main power is absent and notify by SMS if battery is low.

In the figure above SHAULA-V10 is shown labelled for important parts , we would explain these parts one by one .

1:  STATUS LEDs
This is group of four LEDs that indicate different states and provide important information. Its important to understand these, as these can be very helpful in debugging and troubleshooting. The four LEDs are  RED, GREEN, ORANGE and BLUE marked  LA, LB ,LC and LD respectively.

  • LA (Red) : Indicates state of intrusion alarm input. If the input at pin-7 of IDC connector is Low this LED will be ON, which indicates that SHAULA-V10 received an Intrusion alarm signal  from the alarm system.
  • LB (Green) : Indicates state of panic alarm input. If the input at pin-8 of IDC connector is Low this LED will be ON, which indicates that SHAULA-V10 received a panic alarm signal  from the alarm system.
  • LC (Orange) : Indicates state of fire alarm input. If the input at pin-9 of IDC connector is Low this LED will be ON, which indicates that SHAULA-V10 received a fire alarm signal  from the alarm system.
  • LD(Blue) : Indicates state of arming. If the input at pin-10 of IDC connector is Low this LED will be ON, which indicates that SHAULA-V10 received a  signal  from the alarm system indicating that the system is Armed, when this LED is OFF it indicated the system is disarmed.

2:  OPERATION LEDs

This is group of three LEDs that indicate different operational states states of SHAULA-V10. The three  LEDs are  RED, BLE and GREEN marked  PW, RI, and NW respectively.

  • PW(Red) : Indicates power status of SHAULA-V10 as soon as power is applied to SHAULA-V10 this LED will be ON, If the power is not applied it will be OFF.
  • RI(Blue) : Indicates state of incoming SMS or Calls. Its equivalent to the ringer of a phone. It will be ON when there is an incoming call and will blink once for an SMS received.
  • NW(Green) : Indicates state of  network connection.
    • Flash@inverval 800ms: GSM not yet registered to cell phone network.
    • Flash@inverval 3000ms: GSM registered to cell phone network.

3: IDC CONNECTOR

In order to work properly,SHAULA-V10 requires a few signals to work with , which should be made available on the IDC connector .The IDC connector is a 14 pin (2×7) connector. The pin-outs are as follows. (PIN One is marked as red)

Capture22

IDC Cable

pinouts

PINOUTS

  • V+ : Its the first pin of the cable ,denoted by the red wire in the cable, the second wire is also the same V+, It can accept 9V-24VDC input. It is recommended to use 12V or 9V.
  • GND: Its the ground wire.
  • NC: not connected, Do not connect this wire.
  • Intrusion Alarm signal : its the 7th wire, If the wire has a Low signal , SHAULA-V10 identifies an intrusion Alarm and will switch on LED LA as explained in the Status LEDs section. If the signal is not Low , LED LA will be OFF indicating no Intrusion alarm.
  • Panic Alarm signal : its the 8th wire, If the wire has a Low signal , SHAULA-V10 identifies a panic Alarm and will switch on LED LB as explained in the Status LEDs section. If the signal is not Low , LED LB will be OFF indicating no panic alarm.
  • Fire Alarm signal : its the 9th wire, If the wire has a Low signal , SHAULA-V10 identifies a fire Alarm and will switch on LED LC as explained in the Status LEDs section. If the signal is not Low , LED LC will be OFF indicating no Fire alarm.
  • Arming Status signal : its the 10th wire, If the wire has a Low signal , SHAULA-V10 identifies that the Alarm system is  Armed and will switch on LED LD as explained in the Status LEDs section. If the signal is not Low , LED LD will be OFF indicating system is disarmed.
  • Arm disarm pin: It is an output pin and will provide a pulse of Low signal in order to Arm or disarm the Alarm system.

4: GATE AND DOOR RELAY OUTPUTS

SHAULA-V10 can control gate and door using two on board relays. Common and Normal Open signals of both the relays are provided on this connector. Use`N01 and NC1` outputs for gate and `N02 and NC2` outputs for gate.

5: STATUS DISPLAY

This display helps in debugging and troubleshooting , It indicates different states of the operations, It shows when an SMS is received or sent , call is received or made, etc

DISPLAY

OPERATION STATUS

PROGRAMMING STATUS
2

SHAULA-V10 initializing and is not yet ready

Admin number is not yet programmed
1

SHAULA-V10 initializing and is not yet ready

Admin number is  programmed
3  SHAULA-V10 is trying to register to network  Admin number is not yet programmed
4  SHAULA-V10 is trying to register to network  Admin number is  programmed
6   SHAULA-V10 is now in registered to network section*  Admin number is not yet programmed
5  SHAULA-V10 is now in registered to network section*  Admin number is  programmed
8  incoming Call(SHUALA-V10 is receiving a call)  N/A
 Outgoing Call (SHUALA-V10 is making a call)  N/A
9  incoming SMS (SHUALA-V10 has received SMS)  N/A
10  Outgoing SMS (SHUALA-V10 is sending SMS)  N/A

* even if the SIM card has not yet, The operation for  registered to network condition has started.

6: EXTERNAL ANTENNA CONNECTOR

In some cases where signals at the SHAULA-V10 location are weak , an external antenna can be connected. A U.Fl antenna connector is thus provided.
ufl-rp-sma

7: POWER CONNECTOR 

A connector is available for providing the power via a screw terminal connector.

 

Posted in:
Tagged with: